add ST7789 240x240 and ILI9225
This commit is contained in:
moononournation
parent
f2483886a5
commit
f3d3049115
|
|
@ -0,0 +1,5 @@
|
|||
{
|
||||
"files.associations": {
|
||||
"queue": "cpp"
|
||||
}
|
||||
}
|
||||
|
|
@ -0,0 +1,66 @@
|
|||
// Change the width and height if required (defined in portrait mode)
|
||||
// or use the constructor to over-ride defaults
|
||||
#define TFT_WIDTH 176
|
||||
#define TFT_HEIGHT 220
|
||||
|
||||
/* ILI9225 LCD Registers */
|
||||
#define ILI9225_DRIVER_OUTPUT_CTRL (0x01u) // Driver Output Control
|
||||
#define ILI9225_LCD_AC_DRIVING_CTRL (0x02u) // LCD AC Driving Control
|
||||
#define ILI9225_ENTRY_MODE (0x03u) // Entry Mode
|
||||
#define ILI9225_DISP_CTRL1 (0x07u) // Display Control 1
|
||||
#define ILI9225_BLANK_PERIOD_CTRL1 (0x08u) // Blank Period Control
|
||||
#define ILI9225_FRAME_CYCLE_CTRL (0x0Bu) // Frame Cycle Control
|
||||
#define ILI9225_INTERFACE_CTRL (0x0Cu) // Interface Control
|
||||
#define ILI9225_OSC_CTRL (0x0Fu) // Osc Control
|
||||
#define ILI9225_POWER_CTRL1 (0x10u) // Power Control 1
|
||||
#define ILI9225_POWER_CTRL2 (0x11u) // Power Control 2
|
||||
#define ILI9225_POWER_CTRL3 (0x12u) // Power Control 3
|
||||
#define ILI9225_POWER_CTRL4 (0x13u) // Power Control 4
|
||||
#define ILI9225_POWER_CTRL5 (0x14u) // Power Control 5
|
||||
#define ILI9225_VCI_RECYCLING (0x15u) // VCI Recycling
|
||||
#define ILI9225_RAM_ADDR_SET1 (0x20u) // Horizontal GRAM Address Set
|
||||
#define ILI9225_RAM_ADDR_SET2 (0x21u) // Vertical GRAM Address Set
|
||||
#define ILI9225_GRAM_DATA_REG (0x22u) // GRAM Data Register
|
||||
#define ILI9225_GATE_SCAN_CTRL (0x30u) // Gate Scan Control Register
|
||||
#define ILI9225_VERTICAL_SCROLL_CTRL1 (0x31u) // Vertical Scroll Control 1 Register
|
||||
#define ILI9225_VERTICAL_SCROLL_CTRL2 (0x32u) // Vertical Scroll Control 2 Register
|
||||
#define ILI9225_VERTICAL_SCROLL_CTRL3 (0x33u) // Vertical Scroll Control 3 Register
|
||||
#define ILI9225_PARTIAL_DRIVING_POS1 (0x34u) // Partial Driving Position 1 Register
|
||||
#define ILI9225_PARTIAL_DRIVING_POS2 (0x35u) // Partial Driving Position 2 Register
|
||||
#define ILI9225_HORIZONTAL_WINDOW_ADDR1 (0x36u) // Horizontal Address Start Position
|
||||
#define ILI9225_HORIZONTAL_WINDOW_ADDR2 (0x37u) // Horizontal Address End Position
|
||||
#define ILI9225_VERTICAL_WINDOW_ADDR1 (0x38u) // Vertical Address Start Position
|
||||
#define ILI9225_VERTICAL_WINDOW_ADDR2 (0x39u) // Vertical Address End Position
|
||||
#define ILI9225_GAMMA_CTRL1 (0x50u) // Gamma Control 1
|
||||
#define ILI9225_GAMMA_CTRL2 (0x51u) // Gamma Control 2
|
||||
#define ILI9225_GAMMA_CTRL3 (0x52u) // Gamma Control 3
|
||||
#define ILI9225_GAMMA_CTRL4 (0x53u) // Gamma Control 4
|
||||
#define ILI9225_GAMMA_CTRL5 (0x54u) // Gamma Control 5
|
||||
#define ILI9225_GAMMA_CTRL6 (0x55u) // Gamma Control 6
|
||||
#define ILI9225_GAMMA_CTRL7 (0x56u) // Gamma Control 7
|
||||
#define ILI9225_GAMMA_CTRL8 (0x57u) // Gamma Control 8
|
||||
#define ILI9225_GAMMA_CTRL9 (0x58u) // Gamma Control 9
|
||||
#define ILI9225_GAMMA_CTRL10 (0x59u) // Gamma Control 10
|
||||
|
||||
#define TFT_INVOFF 0x20
|
||||
#define TFT_INVON 0x21
|
||||
#define TFT_SWRST 0x28
|
||||
|
||||
// Delay between some initialisation commands
|
||||
#define TFT_INIT_DELAY 0x80 // Not used unless commandlist invoked
|
||||
|
||||
// autoincrement modes (register ILI9225_ENTRY_MODE, bit 5..3 )
|
||||
enum autoIncMode_t { R2L_BottomUp, BottomUp_R2L, L2R_BottomUp, BottomUp_L2R, R2L_TopDown, TopDown_R2L, L2R_TopDown, TopDown_L2R };
|
||||
|
||||
// correspondig modes if orientation changed:
|
||||
const autoIncMode_t modeTab [3][8] = {
|
||||
// { R2L_BottomUp, BottomUp_R2L, L2R_BottomUp, BottomUp_L2R, R2L_TopDown, TopDown_R2L, L2R_TopDown, TopDown_L2R }//
|
||||
/* 90° */ { BottomUp_L2R, L2R_BottomUp, TopDown_L2R, L2R_TopDown, BottomUp_R2L, R2L_BottomUp, TopDown_R2L, R2L_TopDown },
|
||||
/*180° */ { L2R_TopDown , TopDown_L2R, R2L_TopDown, TopDown_R2L, L2R_BottomUp, BottomUp_L2R, R2L_BottomUp, BottomUp_R2L},
|
||||
/*270° */ { TopDown_R2L , R2L_TopDown, BottomUp_R2L, R2L_BottomUp, TopDown_L2R, L2R_TopDown, BottomUp_L2R, L2R_BottomUp}
|
||||
};
|
||||
|
||||
#define TFT_CASET 0x20
|
||||
#define TFT_PASET 0x21
|
||||
#define TFT_RAMWR 0x22
|
||||
#define TFT_RAMRD 0x23
|
||||
|
|
@ -0,0 +1,122 @@
|
|||
|
||||
// This is the command sequence that initialises the ILI9225 driver
|
||||
//
|
||||
// This setup information uses simple 8 bit SPI writecommand() and writedata() functions
|
||||
//
|
||||
// See ST7735_Setup.h file for an alternative format
|
||||
|
||||
{
|
||||
/* Start Initial Sequence */
|
||||
|
||||
//LCD Init For 2.2inch LCD Panel with ILI9225.
|
||||
writecommand(ILI9225_POWER_CTRL1);
|
||||
writedata(0x00);writedata(0x00); // Set SAP,DSTB,STB
|
||||
writecommand(ILI9225_POWER_CTRL2);
|
||||
writedata(0x00);writedata(0x00); // Set APON,PON,AON,VCI1EN,VC
|
||||
writecommand(ILI9225_POWER_CTRL3);
|
||||
writedata(0x00);writedata(0x00); // Set BT,DC1,DC2,DC3
|
||||
writecommand(ILI9225_POWER_CTRL4);
|
||||
writedata(0x00);writedata(0x00); // Set GVDD
|
||||
writecommand(ILI9225_POWER_CTRL5);
|
||||
writedata(0x00);writedata(0x00); // Set VCOMH/VCOML voltage
|
||||
spi_end();
|
||||
delay(40);
|
||||
spi_begin();
|
||||
|
||||
// Power-on sequence
|
||||
writecommand(ILI9225_POWER_CTRL2);
|
||||
writedata(0x00);writedata(0x18); // Set APON,PON,AON,VCI1EN,VC
|
||||
writecommand(ILI9225_POWER_CTRL3);
|
||||
writedata(0x61);writedata(0x21); // Set BT,DC1,DC2,DC3
|
||||
writecommand(ILI9225_POWER_CTRL4);
|
||||
writedata(0x00);writedata(0x6F); // Set GVDD /*007F 0088 */
|
||||
writecommand(ILI9225_POWER_CTRL5);
|
||||
writedata(0x49);writedata(0x5F); // Set VCOMH/VCOML voltage
|
||||
writecommand(ILI9225_POWER_CTRL1);
|
||||
writedata(0x08);writedata(0x00); // Set SAP,DSTB,STB
|
||||
spi_end();
|
||||
delay(10);
|
||||
spi_begin();
|
||||
|
||||
writecommand(ILI9225_POWER_CTRL2);
|
||||
writedata(0x10);writedata(0x3B); // Set APON,PON,AON,VCI1EN,VC
|
||||
spi_end();
|
||||
delay(50);
|
||||
spi_begin();
|
||||
|
||||
writecommand(ILI9225_DRIVER_OUTPUT_CTRL);
|
||||
writedata(0x01);writedata(0x1C); // set the display line number and display direction
|
||||
writecommand(ILI9225_LCD_AC_DRIVING_CTRL);
|
||||
writedata(0x01);writedata(0x00); // set 1 line inversion
|
||||
writecommand(ILI9225_ENTRY_MODE);
|
||||
writedata(0x10);writedata(0x38); // set GRAM write direction and BGR=1
|
||||
writecommand(ILI9225_DISP_CTRL1);
|
||||
writedata(0x00);writedata(0x00); // Display off
|
||||
writecommand(ILI9225_BLANK_PERIOD_CTRL1);
|
||||
writedata(0x08);writedata(0x08); // set the back porch and front porch
|
||||
writecommand(ILI9225_FRAME_CYCLE_CTRL);
|
||||
writedata(0x11);writedata(0x00); // set the clocks number per line
|
||||
writecommand(ILI9225_INTERFACE_CTRL);
|
||||
writedata(0x00);writedata(0x00); // CPU interface
|
||||
writecommand(ILI9225_OSC_CTRL);
|
||||
writedata(0x0D);writedata(0x01); // Set Osc /*0e01*/
|
||||
writecommand(ILI9225_VCI_RECYCLING);
|
||||
writedata(0x00);writedata(0x20); // Set VCI recycling
|
||||
writecommand(ILI9225_RAM_ADDR_SET1);
|
||||
writedata(0x00);writedata(0x00); // RAM Address
|
||||
writecommand(ILI9225_RAM_ADDR_SET2);
|
||||
writedata(0x00);writedata(0x00); // RAM Address
|
||||
|
||||
/* Set GRAM area */
|
||||
writecommand(ILI9225_GATE_SCAN_CTRL);
|
||||
writedata(0x00);writedata(0x00);
|
||||
writecommand(ILI9225_VERTICAL_SCROLL_CTRL1);
|
||||
writedata(0x00);writedata(0xDB);
|
||||
writecommand(ILI9225_VERTICAL_SCROLL_CTRL2);
|
||||
writedata(0x00);writedata(0x00);
|
||||
writecommand(ILI9225_VERTICAL_SCROLL_CTRL3);
|
||||
writedata(0x00);writedata(0x00);
|
||||
writecommand(ILI9225_PARTIAL_DRIVING_POS1);
|
||||
writedata(0x00);writedata(0xDB);
|
||||
writecommand(ILI9225_PARTIAL_DRIVING_POS2);
|
||||
writedata(0x00);writedata(0x00);
|
||||
writecommand(ILI9225_HORIZONTAL_WINDOW_ADDR1);
|
||||
writedata(0x00);writedata(0xAF);
|
||||
writecommand(ILI9225_HORIZONTAL_WINDOW_ADDR2);
|
||||
writedata(0x00);writedata(0x00);
|
||||
writecommand(ILI9225_VERTICAL_WINDOW_ADDR1);
|
||||
writedata(0x00);writedata(0xDB);
|
||||
writecommand(ILI9225_VERTICAL_WINDOW_ADDR2);
|
||||
writedata(0x00);writedata(0x00);
|
||||
|
||||
/* Set GAMMA curve */
|
||||
writecommand(ILI9225_GAMMA_CTRL1);
|
||||
writedata(0x00);writedata(0x00);
|
||||
writecommand(ILI9225_GAMMA_CTRL2);
|
||||
writedata(0x08);writedata(0x08);
|
||||
writecommand(ILI9225_GAMMA_CTRL3);
|
||||
writedata(0x08);writedata(0x0A);
|
||||
writecommand(ILI9225_GAMMA_CTRL4);
|
||||
writedata(0x00);writedata(0x0A);
|
||||
writecommand(ILI9225_GAMMA_CTRL5);
|
||||
writedata(0x0A);writedata(0x08);
|
||||
writecommand(ILI9225_GAMMA_CTRL6);
|
||||
writedata(0x08);writedata(0x08);
|
||||
writecommand(ILI9225_GAMMA_CTRL7);
|
||||
writedata(0x00);writedata(0x00);
|
||||
writecommand(ILI9225_GAMMA_CTRL8);
|
||||
writedata(0x0A);writedata(0x00);
|
||||
writecommand(ILI9225_GAMMA_CTRL9);
|
||||
writedata(0x07);writedata(0x10);
|
||||
writecommand(ILI9225_GAMMA_CTRL10);
|
||||
writedata(0x07);writedata(0x10);
|
||||
|
||||
writecommand(ILI9225_DISP_CTRL1);
|
||||
writedata(0x00);writedata(0x12);
|
||||
|
||||
spi_end();
|
||||
delay(50);
|
||||
spi_begin();
|
||||
writecommand(ILI9225_DISP_CTRL1);
|
||||
writedata(0x10);writedata(0x17);
|
||||
}
|
||||
|
|
@ -0,0 +1,25 @@
|
|||
|
||||
// This is the command sequence that rotates the ILI9225 driver coordinate frame
|
||||
|
||||
rotation = m % 4; // Limit the range of values to 0-3
|
||||
|
||||
// writecommand(TFT_MADCTL);
|
||||
switch (rotation) {
|
||||
case 0:
|
||||
// writedata(TFT_MAD_MY | TFT_MAD_MV | TFT_MAD_BGR);
|
||||
_width = _init_width;
|
||||
_height = _init_height;
|
||||
break;
|
||||
case 1:
|
||||
_width = _init_height;
|
||||
_height = _init_width;
|
||||
break;
|
||||
case 2:
|
||||
_width = _init_width;
|
||||
_height = _init_height;
|
||||
break;
|
||||
case 3:
|
||||
_width = _init_height;
|
||||
_height = _init_width;
|
||||
break;
|
||||
}
|
||||
|
|
@ -1,7 +1,11 @@
|
|||
// Change the width and height if required (defined in portrait mode)
|
||||
// or use the constructor to over-ride defaults
|
||||
#ifndef TFT_WIDTH
|
||||
#define TFT_WIDTH 240
|
||||
#define TFT_HEIGHT 240
|
||||
#endif
|
||||
#ifndef TFT_HEIGHT
|
||||
#define TFT_HEIGHT 320
|
||||
#endif
|
||||
|
||||
#define CGRAM_OFFSET
|
||||
|
||||
|
|
|
|||
|
|
@ -6,14 +6,20 @@
|
|||
{
|
||||
static const uint8_t PROGMEM
|
||||
st7789[] = {
|
||||
#ifdef IPS_LCD
|
||||
9,
|
||||
#else
|
||||
8,
|
||||
#endif
|
||||
TFT_SWRST, TFT_INIT_DELAY, 150,
|
||||
TFT_SLPOUT, TFT_INIT_DELAY, 255,
|
||||
TFT_COLMOD, 1+TFT_INIT_DELAY, 0x55, 10,
|
||||
TFT_MADCTL, 1, TFT_MAD_RGB,
|
||||
TFT_CASET, 4, 0x00, 0x00, 0x00, 0xF0,
|
||||
TFT_PASET, 4, 0x00, 0x00, 0x00, 0xF0,
|
||||
#ifdef IPS_LCD
|
||||
TFT_INVON, TFT_INIT_DELAY, 10,
|
||||
#endif
|
||||
TFT_NORON, TFT_INIT_DELAY, 10,
|
||||
TFT_DISPON, TFT_INIT_DELAY, 255
|
||||
};
|
||||
|
|
|
|||
|
|
@ -22,13 +22,21 @@
|
|||
_width = _init_width;
|
||||
_height = _init_height;
|
||||
colstart = 0;
|
||||
#if (TFT_HEIGHT == 240)
|
||||
rowstart = 80;
|
||||
#else
|
||||
rowstart = 0;
|
||||
#endif
|
||||
break;
|
||||
case 3: // Inverted landscape
|
||||
writedata(TFT_MAD_MV | TFT_MAD_MY | TFT_MAD_RGB);
|
||||
_width = _init_height;
|
||||
_height = _init_width;
|
||||
#if (TFT_HEIGHT == 240)
|
||||
colstart = 80;
|
||||
#else
|
||||
colstart = 0;
|
||||
#endif
|
||||
rowstart = 0;
|
||||
break;
|
||||
}
|
||||
|
|
|
|||
|
|
@ -356,6 +356,9 @@ void TFT_eSPI::init(uint8_t tc)
|
|||
#elif defined (ST7789_DRIVER)
|
||||
#include "TFT_Drivers/ST7789_Init.h"
|
||||
|
||||
#elif defined (ILI9225_DRIVER)
|
||||
#include "TFT_Drivers/ILI9225_Init.h"
|
||||
|
||||
#endif
|
||||
|
||||
spi_end();
|
||||
|
|
@ -404,6 +407,9 @@ void TFT_eSPI::setRotation(uint8_t m)
|
|||
#elif defined (ST7789_DRIVER)
|
||||
#include "TFT_Drivers/ST7789_Rotation.h"
|
||||
|
||||
#elif defined (ILI9225_DRIVER)
|
||||
#include "TFT_Drivers/ILI9225_Rotation.h"
|
||||
|
||||
#endif
|
||||
|
||||
delayMicroseconds(10);
|
||||
|
|
|
|||
21
User_Setup.h
21
User_Setup.h
|
|
@ -15,7 +15,7 @@
|
|||
// ##################################################################################
|
||||
|
||||
// Only define one driver, the other ones must be commented out
|
||||
#define ILI9341_DRIVER
|
||||
// #define ILI9341_DRIVER
|
||||
// #define ST7735_DRIVER
|
||||
// #define ILI9163_DRIVER
|
||||
// #define S6D02A1_DRIVER
|
||||
|
|
@ -24,7 +24,11 @@
|
|||
// #define ILI9481_DRIVER
|
||||
// #define ILI9486_DRIVER
|
||||
// #define ILI9488_DRIVER
|
||||
//#define ST7789_DRIVER
|
||||
#define ST7789_DRIVER
|
||||
// #define ILI9225_DRIVER
|
||||
|
||||
// For IPS LCD display
|
||||
// #define IPS_LCD
|
||||
|
||||
// For M5Stack ESP32 module with integrated display ONLY, remove // in line below
|
||||
// #define M5STACK
|
||||
|
|
@ -32,8 +36,9 @@
|
|||
// For ST7735 and ILI9163 ONLY, define the pixel width and height in portrait orientation
|
||||
// #define TFT_WIDTH 80
|
||||
// #define TFT_WIDTH 128
|
||||
//#define TFT_HEIGHT 160
|
||||
// #define TFT_HEIGHT 128
|
||||
// #define TFT_HEIGHT 160
|
||||
// #define TFT_HEIGHT 240
|
||||
|
||||
// For ST7735 ONLY, define the type of display, originally this was based on the
|
||||
// colour of the tab on the screen protector film but this is not always true, so try
|
||||
|
|
@ -91,9 +96,9 @@
|
|||
// ###### EDIT THE PIN NUMBERS IN THE LINES FOLLOWING TO SUIT YOUR ESP8266 SETUP ######
|
||||
|
||||
// For NodeMCU - use pin numbers in the form PIN_Dx where Dx is the NodeMCU pin designation
|
||||
#define TFT_CS PIN_D8 // Chip select control pin D8
|
||||
#define TFT_DC PIN_D3 // Data Command control pin
|
||||
#define TFT_RST PIN_D4 // Reset pin (could connect to NodeMCU RST, see next line)
|
||||
#define TFT_CS 5 // Chip select control pin D8
|
||||
#define TFT_DC 16 // Data Command control pin
|
||||
#define TFT_RST 17 // Reset pin (could connect to NodeMCU RST, see next line)
|
||||
//#define TFT_RST -1 // Set TFT_RST to -1 if the display RESET is connected to NodeMCU RST or 3.3V
|
||||
|
||||
//#define TOUCH_CS PIN_D2 // Chip select pin (T_CS) of touch screen
|
||||
|
|
@ -234,9 +239,9 @@
|
|||
// #define SPI_FREQUENCY 5000000
|
||||
// #define SPI_FREQUENCY 10000000
|
||||
// #define SPI_FREQUENCY 20000000
|
||||
#define SPI_FREQUENCY 27000000 // Actually sets it to 26.67MHz = 80/3
|
||||
// #define SPI_FREQUENCY 27000000 // Actually sets it to 26.67MHz = 80/3
|
||||
// #define SPI_FREQUENCY 40000000 // Maximum to use SPIFFS
|
||||
// #define SPI_FREQUENCY 80000000
|
||||
#define SPI_FREQUENCY 80000000
|
||||
|
||||
#define SPI_READ_FREQUENCY 20000000 // Optional reduced SPI frequency for reading TFT
|
||||
|
||||
|
|
|
|||
|
|
@ -38,10 +38,12 @@
|
|||
//#include <User_Setups/Setup15_HX8357D.h> // Setup file configured for HX8357D (untested)
|
||||
//#include <User_Setups/Setup16_ILI9488_Parallel.h> // Setup file for the ESP32 with parallel bus TFT
|
||||
//#include <User_Setups/Setup17_ePaper.h> // Setup file for any Waveshare ePaper display
|
||||
//#include <User_Setups/Setup18_ST7789.h> // Setup file configured for HX8357D (untested)
|
||||
//#include <User_Setups/Setup18_ST7789.h> // Setup file configured for ST7789
|
||||
//#include <User_Setups/Setup19_ST7735_80x160.h> // Setup file configured for ST7735 80x160 display
|
||||
//#include <User_Setups/Setup20_ILI9488.h> // Setup file for ESP8266 and ILI9488 SPI bus TFT
|
||||
//#include <User_Setups/Setup21_ILI9488.h> // Setup file for ESP32 and ILI9488 SPI bus TFT
|
||||
//#include <User_Setups/Setup22_ST7789_240x240.h> // Setup file configured for ST7789 240x240 display
|
||||
//#include <User_Setups/Setup23_ILI9225.h> // Setup file for ESP32 and ILI9225 SPI bus TFT
|
||||
|
||||
//#include <User_Setups/SetupX_Template.h>
|
||||
|
||||
|
|
@ -92,6 +94,9 @@
|
|||
#elif defined (ST7789_DRIVER)
|
||||
#include "TFT_Drivers/ST7789_Defines.h"
|
||||
#define TFT_DRIVER 0x7789
|
||||
#elif defined (ILI9225_DRIVER)
|
||||
#include "TFT_Drivers/ILI9225_Defines.h"
|
||||
#define TFT_DRIVER 0x9225
|
||||
#elif defined (XYZZY_DRIVER) // <<<<<<<<<<<<<<<<<<<<<<<< ADD NEW DRIVER HERE
|
||||
#include "TFT_Drivers/XYZZY_Defines.h"
|
||||
#define TFT_DRIVER 0x0000
|
||||
|
|
|
|||
|
|
@ -19,6 +19,15 @@
|
|||
//#define ILI9163_DRIVER
|
||||
//#define S6D02A1_DRIVER
|
||||
#define RPI_ILI9486_DRIVER // 20MHz maximum SPI
|
||||
//#define HX8357D_DRIVER
|
||||
//#define ILI9481_DRIVER
|
||||
//#define ILI9486_DRIVER
|
||||
//#define ILI9488_DRIVER
|
||||
//#define ST7789_DRIVER
|
||||
//#define ILI9225_DRIVER
|
||||
|
||||
// For IPS LCD display
|
||||
//#define IPS_LCD
|
||||
|
||||
// For M5Stack ESP32 module with integrated display ONLY, remove // in line below
|
||||
//#define M5STACK
|
||||
|
|
@ -26,8 +35,9 @@
|
|||
// For ST7735 and ILI9163 ONLY, define the pixel width and height in portrait orientation
|
||||
//#define TFT_WIDTH 80
|
||||
//#define TFT_WIDTH 128
|
||||
//#define TFT_HEIGHT 160
|
||||
//#define TFT_HEIGHT 128
|
||||
//#define TFT_HEIGHT 160
|
||||
//#define TFT_HEIGHT 240
|
||||
|
||||
// For ST7735 ONLY, define the type of display, originally this was based on the
|
||||
// colour of the tab on the screen protector film but this is not always true, so try
|
||||
|
|
|
|||
|
|
@ -19,6 +19,15 @@
|
|||
//#define ILI9163_DRIVER
|
||||
//#define S6D02A1_DRIVER
|
||||
#define RPI_ILI9486_DRIVER // 20MHz maximum SPI
|
||||
//#define HX8357D_DRIVER
|
||||
//#define ILI9481_DRIVER
|
||||
//#define ILI9486_DRIVER
|
||||
//#define ILI9488_DRIVER
|
||||
//#define ST7789_DRIVER
|
||||
//#define ILI9225_DRIVER
|
||||
|
||||
// For IPS LCD display
|
||||
//#define IPS_LCD
|
||||
|
||||
// For M5Stack ESP32 module with integrated display ONLY, remove // in line below
|
||||
//#define M5STACK
|
||||
|
|
@ -26,8 +35,9 @@
|
|||
// For ST7735 and ILI9163 ONLY, define the pixel width and height in portrait orientation
|
||||
//#define TFT_WIDTH 80
|
||||
//#define TFT_WIDTH 128
|
||||
//#define TFT_HEIGHT 160
|
||||
//#define TFT_HEIGHT 128
|
||||
//#define TFT_HEIGHT 160
|
||||
//#define TFT_HEIGHT 240
|
||||
|
||||
// For ST7735 ONLY, define the type of display, originally this was based on the
|
||||
// colour of the tab on the screen protector film but this is not always true, so try
|
||||
|
|
|
|||
|
|
@ -19,6 +19,15 @@
|
|||
//#define ILI9163_DRIVER
|
||||
//#define S6D02A1_DRIVER
|
||||
//#define RPI_ILI9486_DRIVER // 20MHz maximum SPI
|
||||
//#define HX8357D_DRIVER
|
||||
//#define ILI9481_DRIVER
|
||||
//#define ILI9486_DRIVER
|
||||
//#define ILI9488_DRIVER
|
||||
//#define ST7789_DRIVER
|
||||
//#define ILI9225_DRIVER
|
||||
|
||||
// For IPS LCD display
|
||||
//#define IPS_LCD
|
||||
|
||||
// For M5Stack ESP32 module with integrated display ONLY, remove // in line below
|
||||
#define M5STACK
|
||||
|
|
@ -26,8 +35,9 @@
|
|||
// For ST7735 and ILI9163 ONLY, define the pixel width and height in portrait orientation
|
||||
//#define TFT_WIDTH 80
|
||||
//#define TFT_WIDTH 128
|
||||
//#define TFT_HEIGHT 160
|
||||
//#define TFT_HEIGHT 128
|
||||
//#define TFT_HEIGHT 160
|
||||
//#define TFT_HEIGHT 240
|
||||
|
||||
// For ST7735 ONLY, define the type of display, originally this was based on the
|
||||
// colour of the tab on the screen protector film but this is not always true, so try
|
||||
|
|
|
|||
|
|
@ -20,6 +20,14 @@
|
|||
//#define S6D02A1_DRIVER
|
||||
//#define RPI_ILI9486_DRIVER // 20MHz maximum SPI
|
||||
#define HX8357D_DRIVER
|
||||
//#define ILI9481_DRIVER
|
||||
//#define ILI9486_DRIVER
|
||||
//#define ILI9488_DRIVER
|
||||
//#define ST7789_DRIVER
|
||||
//#define ILI9225_DRIVER
|
||||
|
||||
// For IPS LCD display
|
||||
//#define IPS_LCD
|
||||
|
||||
// For M5Stack ESP32 module with integrated display ONLY, remove // in line below
|
||||
//#define M5STACK
|
||||
|
|
@ -27,8 +35,9 @@
|
|||
// For ST7735 and ILI9163 ONLY, define the pixel width and height in portrait orientation
|
||||
//#define TFT_WIDTH 80
|
||||
//#define TFT_WIDTH 128
|
||||
//#define TFT_HEIGHT 160
|
||||
//#define TFT_HEIGHT 128
|
||||
//#define TFT_HEIGHT 160
|
||||
//#define TFT_HEIGHT 240
|
||||
|
||||
// For ST7735 ONLY, define the type of display, originally this was based on the
|
||||
// colour of the tab on the screen protector film but this is not always true, so try
|
||||
|
|
|
|||
|
|
@ -22,8 +22,13 @@
|
|||
//#define RPI_ILI9486_DRIVER // 20MHz maximum SPI
|
||||
//#define HX8357D_DRIVER
|
||||
//#define ILI9481_DRIVER
|
||||
//#define ILI9486_DRIVER
|
||||
//#define ILI9488_DRIVER
|
||||
#define ST7789_DRIVER
|
||||
//#define ILI9225_DRIVER
|
||||
|
||||
// For IPS LCD display
|
||||
//#define IPS_LCD
|
||||
|
||||
// For M5Stack ESP32 module with integrated display ONLY, remove // in line below
|
||||
//#define M5STACK
|
||||
|
|
@ -31,8 +36,9 @@
|
|||
// For ST7735 and ILI9163 ONLY, define the pixel width and height in portrait orientation
|
||||
//#define TFT_WIDTH 80
|
||||
//#define TFT_WIDTH 128
|
||||
//#define TFT_HEIGHT 160
|
||||
//#define TFT_HEIGHT 128
|
||||
//#define TFT_HEIGHT 160
|
||||
//#define TFT_HEIGHT 240
|
||||
|
||||
// For ST7735 ONLY, define the type of display, originally this was based on the
|
||||
// colour of the tab on the screen protector film but this is not always true, so try
|
||||
|
|
|
|||
|
|
@ -19,6 +19,15 @@
|
|||
//#define ILI9163_DRIVER
|
||||
//#define S6D02A1_DRIVER
|
||||
//#define RPI_ILI9486_DRIVER // 20MHz maximum SPI
|
||||
//#define HX8357D_DRIVER
|
||||
//#define ILI9481_DRIVER
|
||||
//#define ILI9486_DRIVER
|
||||
//#define ILI9488_DRIVER
|
||||
//#define ST7789_DRIVER
|
||||
//#define ILI9225_DRIVER
|
||||
|
||||
// For IPS LCD display
|
||||
//#define IPS_LCD
|
||||
|
||||
// For M5Stack ESP32 module with integrated display ONLY, remove // in line below
|
||||
//#define M5STACK
|
||||
|
|
@ -26,8 +35,9 @@
|
|||
// For ST7735 and ILI9163 ONLY, define the pixel width and height in portrait orientation
|
||||
#define TFT_WIDTH 80
|
||||
//#define TFT_WIDTH 128
|
||||
#define TFT_HEIGHT 160
|
||||
//#define TFT_HEIGHT 128
|
||||
#define TFT_HEIGHT 160
|
||||
//#define TFT_HEIGHT 240
|
||||
|
||||
// For ST7735 ONLY, define the type of display, originally this was based on the
|
||||
// colour of the tab on the screen protector film but this is not always true, so try
|
||||
|
|
|
|||
|
|
@ -19,6 +19,15 @@
|
|||
//#define ILI9163_DRIVER
|
||||
//#define S6D02A1_DRIVER
|
||||
//#define RPI_ILI9486_DRIVER // 20MHz maximum SPI
|
||||
//#define HX8357D_DRIVER
|
||||
//#define ILI9481_DRIVER
|
||||
//#define ILI9486_DRIVER
|
||||
//#define ILI9488_DRIVER
|
||||
//#define ST7789_DRIVER
|
||||
//#define ILI9225_DRIVER
|
||||
|
||||
// For IPS LCD display
|
||||
//#define IPS_LCD
|
||||
|
||||
// For M5Stack ESP32 module with integrated display ONLY, remove // in line below
|
||||
//#define M5STACK
|
||||
|
|
@ -26,8 +35,9 @@
|
|||
// For ST7735 and ILI9163 ONLY, define the pixel width and height in portrait orientation
|
||||
//#define TFT_WIDTH 80
|
||||
//#define TFT_WIDTH 128
|
||||
//#define TFT_HEIGHT 160
|
||||
//#define TFT_HEIGHT 128
|
||||
//#define TFT_HEIGHT 160
|
||||
//#define TFT_HEIGHT 240
|
||||
|
||||
// For ST7735 ONLY, define the type of display, originally this was based on the
|
||||
// colour of the tab on the screen protector film but this is not always true, so try
|
||||
|
|
|
|||
|
|
@ -19,7 +19,15 @@
|
|||
//#define ILI9163_DRIVER
|
||||
//#define S6D02A1_DRIVER
|
||||
//#define RPI_ILI9486_DRIVER // 20MHz maximum SPI
|
||||
//#define HX8357D_DRIVER
|
||||
//#define ILI9481_DRIVER
|
||||
//#define ILI9486_DRIVER
|
||||
#define ILI9488_DRIVER
|
||||
//#define ST7789_DRIVER
|
||||
//#define ILI9225_DRIVER
|
||||
|
||||
// For IPS LCD display
|
||||
//#define IPS_LCD
|
||||
|
||||
// For M5Stack ESP32 module with integrated display ONLY, remove // in line below
|
||||
//#define M5STACK
|
||||
|
|
@ -27,8 +35,9 @@
|
|||
// For ST7735 and ILI9163 ONLY, define the pixel width and height in portrait orientation
|
||||
//#define TFT_WIDTH 80
|
||||
//#define TFT_WIDTH 128
|
||||
//#define TFT_HEIGHT 160
|
||||
//#define TFT_HEIGHT 128
|
||||
//#define TFT_HEIGHT 160
|
||||
//#define TFT_HEIGHT 240
|
||||
|
||||
// For ST7735 ONLY, define the type of display, originally this was based on the
|
||||
// colour of the tab on the screen protector film but this is not always true, so try
|
||||
|
|
|
|||
|
|
@ -19,7 +19,15 @@
|
|||
//#define ILI9163_DRIVER
|
||||
//#define S6D02A1_DRIVER
|
||||
//#define RPI_ILI9486_DRIVER // 20MHz maximum SPI
|
||||
//#define HX8357D_DRIVER
|
||||
//#define ILI9481_DRIVER
|
||||
//#define ILI9486_DRIVER
|
||||
#define ILI9488_DRIVER
|
||||
//#define ST7789_DRIVER
|
||||
//#define ILI9225_DRIVER
|
||||
|
||||
// For IPS LCD display
|
||||
//#define IPS_LCD
|
||||
|
||||
// For M5Stack ESP32 module with integrated display ONLY, remove // in line below
|
||||
//#define M5STACK
|
||||
|
|
@ -27,8 +35,9 @@
|
|||
// For ST7735 and ILI9163 ONLY, define the pixel width and height in portrait orientation
|
||||
//#define TFT_WIDTH 80
|
||||
//#define TFT_WIDTH 128
|
||||
//#define TFT_HEIGHT 160
|
||||
//#define TFT_HEIGHT 128
|
||||
//#define TFT_HEIGHT 160
|
||||
//#define TFT_HEIGHT 240
|
||||
|
||||
// For ST7735 ONLY, define the type of display, originally this was based on the
|
||||
// colour of the tab on the screen protector film but this is not always true, so try
|
||||
|
|
|
|||
|
|
@ -0,0 +1,260 @@
|
|||
// USER DEFINED SETTINGS
|
||||
// Set driver type, fonts to be loaded, pins used and SPI control method etc
|
||||
//
|
||||
// See the User_Setup_Select.h file if you wish to be able to define multiple
|
||||
// setups and then easily select which setup file is used by the compiler.
|
||||
//
|
||||
// If this file is edited correctly then all the library example sketches should
|
||||
// run without the need to make any more changes for a particular hardware setup!
|
||||
// Note that some sketches are designed for a particular TFT pixel width/height
|
||||
|
||||
// ##################################################################################
|
||||
//
|
||||
// Section 0. Call up the right driver file and any options for it
|
||||
//
|
||||
// ##################################################################################
|
||||
|
||||
// Only define one driver, the other ones must be commented out
|
||||
//#define ILI9341_DRIVER
|
||||
//#define ST7735_DRIVER
|
||||
//#define ILI9163_DRIVER
|
||||
//#define S6D02A1_DRIVER
|
||||
//#define RPI_ILI9486_DRIVER // 20MHz maximum SPI
|
||||
//#define HX8357D_DRIVER
|
||||
//#define ILI9481_DRIVER
|
||||
//#define ILI9486_DRIVER
|
||||
//#define ILI9488_DRIVER
|
||||
#define ST7789_DRIVER
|
||||
//#define ILI9225_DRIVER
|
||||
|
||||
// For IPS LCD display
|
||||
#define IPS_LCD
|
||||
|
||||
// For M5Stack ESP32 module with integrated display ONLY, remove // in line below
|
||||
//#define M5STACK
|
||||
|
||||
// For ST7735, ST7789 and ILI9163 ONLY, define the pixel width and height in portrait orientation
|
||||
//#define TFT_WIDTH 80
|
||||
//#define TFT_WIDTH 128
|
||||
//#define TFT_HEIGHT 128
|
||||
//#define TFT_HEIGHT 160
|
||||
#define TFT_HEIGHT 240
|
||||
|
||||
// For ST7735 ONLY, define the type of display, originally this was based on the
|
||||
// colour of the tab on the screen protector film but this is not always true, so try
|
||||
// out the different options below if the screen does not display graphics correctly,
|
||||
// e.g. colours wrong, mirror images, or tray pixels at the edges.
|
||||
// Comment out ALL BUT ONE of these options for a ST7735 display driver, save this
|
||||
// this User_Setup file, then rebuild and upload the sketch to the board again:
|
||||
|
||||
//#define ST7735_INITB
|
||||
//#define ST7735_GREENTAB
|
||||
//#define ST7735_GREENTAB2
|
||||
//#define ST7735_GREENTAB3
|
||||
//#define ST7735_GREENTAB128 // For 128 x 128 display
|
||||
//#define ST7735_GREENTAB80160 // For 80 x 160 display
|
||||
//#define ST7735_REDTAB
|
||||
//#define ST7735_BLACKTAB
|
||||
|
||||
// ##################################################################################
|
||||
//
|
||||
// Section 1. Define the pins that are used to interface with the display here
|
||||
//
|
||||
// ##################################################################################
|
||||
|
||||
// We must use hardware SPI, a minimum of 3 GPIO pins is needed.
|
||||
// Typical setup for ESP8266 NodeMCU ESP-12 is :
|
||||
//
|
||||
// Display SDO/MISO to NodeMCU pin D6 (or leave disconnected if not reading TFT)
|
||||
// Display LED to NodeMCU pin VIN (or 5V, see below)
|
||||
// Display SCK to NodeMCU pin D5
|
||||
// Display SDI/MOSI to NodeMCU pin D7
|
||||
// Display DC (RS/AO)to NodeMCU pin D3
|
||||
// Display RESET to NodeMCU pin D4 (or RST, see below)
|
||||
// Display CS to NodeMCU pin D8 (or GND, see below)
|
||||
// Display GND to NodeMCU pin GND (0V)
|
||||
// Display VCC to NodeMCU 5V or 3.3V
|
||||
//
|
||||
// The TFT RESET pin can be connected to the NodeMCU RST pin or 3.3V to free up a control pin
|
||||
//
|
||||
// The DC (Data Command) pin may be labeled AO or RS (Register Select)
|
||||
//
|
||||
// With some displays such as the ILI9341 the TFT CS pin can be connected to GND if no more
|
||||
// SPI devices (e.g. an SD Card) are connected, in this case comment out the #define TFT_CS
|
||||
// line below so it is NOT defined. Other displays such at the ST7735 require the TFT CS pin
|
||||
// to be toggled during setup, so in these cases the TFT_CS line must be defined and connected.
|
||||
//
|
||||
// The NodeMCU D0 pin can be used for RST
|
||||
//
|
||||
// See Section 2. below if DC or CS is connected to D0
|
||||
//
|
||||
// Note: only some versions of the NodeMCU provide the USB 5V on the VIN pin
|
||||
// If 5V is not available at a pin you can use 3.3V but backlight brightness
|
||||
// will be lower.
|
||||
|
||||
|
||||
// ###### EDIT THE PIN NUMBERS IN THE LINES FOLLOWING TO SUIT YOUR ESP8266 SETUP ######
|
||||
|
||||
// For NodeMCU - use pin numbers in the form PIN_Dx where Dx is the NodeMCU pin designation
|
||||
//#define TFT_CS PIN_D8 // Chip select control pin D8
|
||||
#define TFT_DC PIN_D3 // Data Command control pin
|
||||
#define TFT_RST PIN_D4 // Reset pin (could connect to NodeMCU RST, see next line)
|
||||
//#define TFT_RST -1 // Set TFT_RST to -1 if the display RESET is connected to NodeMCU RST or 3.3V
|
||||
|
||||
//#define TOUCH_CS PIN_D2 // Chip select pin (T_CS) of touch screen
|
||||
|
||||
//#define TFT_WR PIN_D2 // Write strobe for modified Raspberry Pi TFT only
|
||||
|
||||
|
||||
// ###### FOR ESP8266 OVERLAP MODE EDIT THE PIN NUMBERS IN THE FOLLOWING LINES ######
|
||||
|
||||
// Overlap mode shares the ESP8266 FLASH SPI bus with the TFT so has a performance impact
|
||||
// but saves pins for other functions.
|
||||
// Use NodeMCU SD0=MISO, SD1=MOSI, CLK=SCLK to connect to TFT in overlap mode
|
||||
|
||||
// In ESP8266 overlap mode the TFT chip select MUST connect to pin D3
|
||||
//#define TFT_CS PIN_D3
|
||||
//#define TFT_DC PIN_D5 // Data Command control pin
|
||||
//#define TFT_RST PIN_D4 // Reset pin (could connect to NodeMCU RST, see next line)
|
||||
//#define TFT_RST -1 // Set TFT_RST to -1 if the display RESET is connected to NodeMCU RST or 3.3V
|
||||
|
||||
// In ESP8266 overlap mode the following must be defined
|
||||
//#define TFT_SPI_OVERLAP
|
||||
|
||||
// ###### EDIT THE PIN NUMBERS IN THE LINES FOLLOWING TO SUIT YOUR ESP32 SETUP ######
|
||||
|
||||
// For ESP32 Dev board (only tested with ILI9341 display)
|
||||
// The hardware SPI can be mapped to any pins
|
||||
|
||||
//#define TFT_MISO 19
|
||||
//#define TFT_MOSI 23
|
||||
//#define TFT_SCLK 18
|
||||
//#define TFT_CS 15 // Chip select control pin
|
||||
//#define TFT_DC 2 // Data Command control pin
|
||||
//#define TFT_RST 4 // Reset pin (could connect to RST pin)
|
||||
//#define TFT_RST -1 // Set TFT_RST to -1 if display RESET is connected to ESP32 board RST
|
||||
|
||||
// For the M5Stack module use these #define lines
|
||||
//#define TFT_MISO 19
|
||||
//#define TFT_MOSI 23
|
||||
//#define TFT_SCLK 18
|
||||
//#define TFT_CS 14 // Chip select control pin
|
||||
//#define TFT_DC 27 // Data Command control pin
|
||||
//#define TFT_RST 33 // Reset pin (could connect to Arduino RESET pin)
|
||||
//#define TFT_BL 32 // LED back-light
|
||||
|
||||
//#define TOUCH_CS 21 // Chip select pin (T_CS) of touch screen
|
||||
|
||||
//#define TFT_WR 22 // Write strobe for modified Raspberry Pi TFT only
|
||||
|
||||
// ###### EDIT THE PINs BELOW TO SUIT YOUR ESP32 PARALLEL TFT SETUP ######
|
||||
|
||||
// The library supports 8 bit parallel TFTs with the ESP32, the pin
|
||||
// selection below is compatible with ESP32 boards in UNO format.
|
||||
// Wemos D32 boards need to be modified, see diagram in Tools folder.
|
||||
// Only ILI9481 and ILI9341 based displays have been tested!
|
||||
|
||||
// Parallel bus is only supported on ESP32
|
||||
// Uncomment line below to use ESP32 Parallel interface instead of SPI
|
||||
|
||||
//#define ESP32_PARALLEL
|
||||
|
||||
// The ESP32 and TFT the pins used for testing are:
|
||||
//#define TFT_CS 33 // Chip select control pin (library pulls permanently low
|
||||
//#define TFT_DC 15 // Data Command control pin - use a pin in the range 0-31
|
||||
//#define TFT_RST 32 // Reset pin, toggles on startup
|
||||
|
||||
//#define TFT_WR 4 // Write strobe control pin - use a pin in the range 0-31
|
||||
//#define TFT_RD 2 // Read strobe control pin - use a pin in the range 0-31
|
||||
|
||||
//#define TFT_D0 12 // Must use pins in the range 0-31 for the data bus
|
||||
//#define TFT_D1 13 // so a single register write sets/clears all bits.
|
||||
//#define TFT_D2 26 // Pins can be randomly assigned, this does not affect
|
||||
//#define TFT_D3 25 // TFT screen update performance.
|
||||
//#define TFT_D4 17
|
||||
//#define TFT_D5 16
|
||||
//#define TFT_D6 27
|
||||
//#define TFT_D7 14
|
||||
|
||||
// ##################################################################################
|
||||
//
|
||||
// Section 2. Define the way the DC and/or CS lines are driven (ESP8266 only)
|
||||
//
|
||||
// ##################################################################################
|
||||
|
||||
// Normally the library uses direct register access for the DC and CS lines for speed
|
||||
// If D0 (GPIO16) is used for CS or DC then a different slower method must be used
|
||||
// Uncomment one line if D0 is used for DC or CS
|
||||
// DC on D0 = 6% performance penalty at 40MHz SPI running graphics test
|
||||
// CS on D0 = 2% performance penalty at 40MHz SPI running graphics test
|
||||
|
||||
// #define D0_USED_FOR_DC
|
||||
// #define D0_USED_FOR_CS
|
||||
|
||||
// ##################################################################################
|
||||
//
|
||||
// Section 3. Define the fonts that are to be used here
|
||||
//
|
||||
// ##################################################################################
|
||||
|
||||
// Comment out the #defines below with // to stop that font being loaded
|
||||
// The ESP8366 and ESP32 have plenty of memory so commenting out fonts is not
|
||||
// normally necessary. If all fonts are loaded the extra FLASH space required is
|
||||
// about 17Kbytes. To save FLASH space only enable the fonts you need!
|
||||
|
||||
#define LOAD_GLCD // Font 1. Original Adafruit 8 pixel font needs ~1820 bytes in FLASH
|
||||
#define LOAD_FONT2 // Font 2. Small 16 pixel high font, needs ~3534 bytes in FLASH, 96 characters
|
||||
#define LOAD_FONT4 // Font 4. Medium 26 pixel high font, needs ~5848 bytes in FLASH, 96 characters
|
||||
#define LOAD_FONT6 // Font 6. Large 48 pixel font, needs ~2666 bytes in FLASH, only characters 1234567890:-.apm
|
||||
#define LOAD_FONT7 // Font 7. 7 segment 48 pixel font, needs ~2438 bytes in FLASH, only characters 1234567890:-.
|
||||
#define LOAD_FONT8 // Font 8. Large 75 pixel font needs ~3256 bytes in FLASH, only characters 1234567890:-.
|
||||
//#define LOAD_FONT8N // Font 8. Alternative to Font 8 above, slightly narrower, so 3 digits fit a 160 pixel TFT
|
||||
#define LOAD_GFXFF // FreeFonts. Include access to the 48 Adafruit_GFX free fonts FF1 to FF48 and custom fonts
|
||||
|
||||
// Comment out the #define below to stop the SPIFFS filing system and smooth font code being loaded
|
||||
// this will save ~20kbytes of FLASH
|
||||
#define SMOOTH_FONT
|
||||
|
||||
// ##################################################################################
|
||||
//
|
||||
// Section 4. Not used
|
||||
//
|
||||
// ##################################################################################
|
||||
|
||||
|
||||
// ##################################################################################
|
||||
//
|
||||
// Section 5. Other options
|
||||
//
|
||||
// ##################################################################################
|
||||
|
||||
// Define the SPI clock frequency, this affects the graphics rendering speed. Too
|
||||
// fast and the TFT driver will not keep up and display corruption appears.
|
||||
// With an ILI9341 display 40MHz works OK, 80MHz sometimes fails
|
||||
// With a ST7735 display more than 27MHz may not work (spurious pixels and lines)
|
||||
// With an ILI9163 display 27 MHz works OK.
|
||||
// The RPi typically only works at 20MHz maximum.
|
||||
|
||||
// #define SPI_FREQUENCY 1000000
|
||||
// #define SPI_FREQUENCY 5000000
|
||||
// #define SPI_FREQUENCY 10000000
|
||||
// #define SPI_FREQUENCY 20000000
|
||||
#define SPI_FREQUENCY 27000000 // Actually sets it to 26.67MHz = 80/3
|
||||
// #define SPI_FREQUENCY 40000000 // Maximum to use SPIFFS
|
||||
// #define SPI_FREQUENCY 80000000
|
||||
|
||||
// The XPT2046 requires a lower SPI clock rate of 2.5MHz so we define that here:
|
||||
#define SPI_TOUCH_FREQUENCY 2500000
|
||||
|
||||
|
||||
// Comment out the following #define if "SPI Transactions" do not need to be
|
||||
// supported. When commented out the code size will be smaller and sketches will
|
||||
// run slightly faster, so leave it commented out unless you need it!
|
||||
|
||||
// Transaction support is needed to work with SD library but not needed with TFT_SdFat
|
||||
// Transaction support is required if other SPI devices are connected.
|
||||
|
||||
// Transactions are automatically enabled by the library for an ESP32 (to use HAL mutex)
|
||||
// so changing it here has no effect
|
||||
|
||||
//#define SUPPORT_TRANSACTIONS
|
||||
|
|
@ -0,0 +1,230 @@
|
|||
// USER DEFINED SETTINGS
|
||||
// Set driver type, fonts to be loaded, pins used and SPI control method etc
|
||||
//
|
||||
// See the User_Setup_Select.h file if you wish to be able to define multiple
|
||||
// setups and then easily select which setup file is used by the compiler.
|
||||
//
|
||||
// If this file is edited correctly then all the library example sketches should
|
||||
// run without the need to make any more changes for a particular hardware setup!
|
||||
|
||||
// ##################################################################################
|
||||
//
|
||||
// Section 0. Call up the right driver file and any options for it
|
||||
//
|
||||
// ##################################################################################
|
||||
|
||||
// Only define one driver, the other ones must be commented out
|
||||
#define ILI9341_DRIVER
|
||||
//#define ST7735_DRIVER
|
||||
//#define ILI9163_DRIVER
|
||||
//#define S6D02A1_DRIVER
|
||||
//#define RPI_ILI9486_DRIVER // 20MHz maximum SPI
|
||||
//#define HX8357D_DRIVER
|
||||
//#define ILI9481_DRIVER
|
||||
//#define ILI9486_DRIVER
|
||||
//#define ILI9488_DRIVER
|
||||
//#define ST7789_DRIVER
|
||||
//#define ILI9225_DRIVER
|
||||
|
||||
// For IPS LCD display
|
||||
//#define IPS_LCD
|
||||
|
||||
// For M5Stack ESP32 module with integrated display ONLY, remove // in line below
|
||||
//#define M5STACK
|
||||
|
||||
// For ST7735 and ILI9163 ONLY, define the pixel width and height in portrait orientation
|
||||
//#define TFT_WIDTH 80
|
||||
//#define TFT_WIDTH 128
|
||||
//#define TFT_HEIGHT 128
|
||||
//#define TFT_HEIGHT 160
|
||||
//#define TFT_HEIGHT 240
|
||||
|
||||
// For ST7735 ONLY, define the type of display, originally this was based on the
|
||||
// colour of the tab on the screen protector film but this is not always true, so try
|
||||
// out the different options below if the screen does not display graphics correctly,
|
||||
// e.g. colours wrong, mirror images, or tray pixels at the edges.
|
||||
// Comment out ALL BUT ONE of these options for a ST7735 display driver, save this
|
||||
// this User_Setup file, then rebuild and upload the sketch to the board again:
|
||||
|
||||
//#define ST7735_INITB
|
||||
//#define ST7735_GREENTAB
|
||||
//#define ST7735_GREENTAB2
|
||||
//#define ST7735_GREENTAB3
|
||||
//#define ST7735_GREENTAB128 // For 128 x 128 display
|
||||
//#define ST7735_GREENTAB80160 // For 80 x 160 display
|
||||
//#define ST7735_REDTAB
|
||||
//#define ST7735_BLACKTAB
|
||||
|
||||
// ##################################################################################
|
||||
//
|
||||
// Section 1. Define the pins that are used to interface with the display here
|
||||
//
|
||||
// ##################################################################################
|
||||
|
||||
// We must use hardware SPI, a minimum of 3 GPIO pins is needed.
|
||||
// Typical setup for ESP8266 NodeMCU ESP-12 is :
|
||||
//
|
||||
// Display SDO/MISO to NodeMCU pin D6 (or leave disconnected if not reading TFT)
|
||||
// Display LED to NodeMCU pin VIN (or 5V, see below)
|
||||
// Display SCK to NodeMCU pin D5
|
||||
// Display SDI/MOSI to NodeMCU pin D7
|
||||
// Display DC (RS/AO)to NodeMCU pin D3
|
||||
// Display RESET to NodeMCU pin D4 (or RST, see below)
|
||||
// Display CS to NodeMCU pin D8 (or GND, see below)
|
||||
// Display GND to NodeMCU pin GND (0V)
|
||||
// Display VCC to NodeMCU 5V or 3.3V
|
||||
//
|
||||
// The TFT RESET pin can be connected to the NodeMCU RST pin or 3.3V to free up a control pin
|
||||
//
|
||||
// The DC (Data Command) pin may be labeled AO or RS (Register Select)
|
||||
//
|
||||
// With some displays such as the ILI9341 the TFT CS pin can be connected to GND if no more
|
||||
// SPI devices (e.g. an SD Card) are connected, in this case comment out the #define TFT_CS
|
||||
// line below so it is NOT defined. Other displays such at the ST7735 require the TFT CS pin
|
||||
// to be toggled during setup, so in these cases the TFT_CS line must be defined and connected.
|
||||
//
|
||||
// The NodeMCU D0 pin can be used for RST
|
||||
//
|
||||
// See Section 2. below if DC or CS is connected to D0
|
||||
//
|
||||
// Note: only some versions of the NodeMCU provide the USB 5V on the VIN pin
|
||||
// If 5V is not available at a pin you can use 3.3V but backlight brightness
|
||||
// will be lower.
|
||||
|
||||
|
||||
// ###### EDIT THE PIN NUMBERS IN THE LINES FOLLOWING TO SUIT YOUR ESP8266 SETUP ######
|
||||
|
||||
// For NodeMCU - use pin numbers in the form PIN_Dx where Dx is the NodeMCU pin designation
|
||||
#define TFT_CS PIN_D8 // Chip select control pin D8
|
||||
#define TFT_DC PIN_D3 // Data Command control pin
|
||||
#define TFT_RST PIN_D4 // Reset pin (could connect to NodeMCU RST, see next line)
|
||||
//#define TFT_RST -1 // Set TFT_RST to -1 if the display RESET is connected to NodeMCU RST or 3.3V
|
||||
|
||||
//#define TOUCH_CS PIN_D1 // Chip select pin (T_CS) of touch screen
|
||||
|
||||
//#define TFT_WR PIN_D2 // Write strobe for modified Raspberry Pi TFT only
|
||||
|
||||
|
||||
// ###### FOR ESP8266 OVERLAP MODE EDIT THE PIN NUMBERS IN THE FOLLOWING LINES ######
|
||||
|
||||
// Overlap mode shares the ESP8266 FLASH SPI bus with the TFT so has a performance impact
|
||||
// but saves pins for other functions.
|
||||
// Use NodeMCU SD0=MISO, SD1=MOSI, CLK=SCLK to connect to TFT in overlap mode
|
||||
|
||||
// In ESP8266 overlap mode the TFT chip select MUST connect to pin D3
|
||||
//#define TFT_CS PIN_D3
|
||||
//#define TFT_DC PIN_D5 // Data Command control pin
|
||||
//#define TFT_RST PIN_D4 // Reset pin (could connect to NodeMCU RST, see next line)
|
||||
//#define TFT_RST -1 // Set TFT_RST to -1 if the display RESET is connected to NodeMCU RST or 3.3V
|
||||
|
||||
// In ESP8266 overlap mode the following must be defined
|
||||
//#define TFT_SPI_OVERLAP
|
||||
|
||||
// ###### EDIT THE PIN NUMBERS IN THE LINES FOLLOWING TO SUIT YOUR ESP32 SETUP ######
|
||||
|
||||
// For ESP32 Dev board (only tested with ILI9341 display)
|
||||
// The hardware SPI can be mapped to any pins
|
||||
|
||||
//#define TFT_MISO 19
|
||||
//#define TFT_MOSI 23
|
||||
//#define TFT_SCLK 18
|
||||
//#define TFT_CS 15 // Chip select control pin
|
||||
//#define TFT_DC 2 // Data Command control pin
|
||||
//#define TFT_RST 4 // Reset pin (could connect to RST pin)
|
||||
//#define TFT_RST -1 // Set TFT_RST to -1 if display RESET is connected to ESP32 board RST
|
||||
|
||||
//#define TOUCH_CS 21 // Chip select pin (T_CS) of touch screen
|
||||
|
||||
//#define TFT_WR 22 // Write strobe for modified Raspberry Pi TFT only
|
||||
|
||||
// For the M5Stack module use these #define lines
|
||||
//#define TFT_MISO 19
|
||||
//#define TFT_MOSI 23
|
||||
//#define TFT_SCLK 18
|
||||
//#define TFT_CS 14 // Chip select control pin
|
||||
//#define TFT_DC 27 // Data Command control pin
|
||||
//#define TFT_RST 33 // Reset pin (could connect to Arduino RESET pin)
|
||||
//#define TFT_BL 32 // LED back-light
|
||||
|
||||
// ##################################################################################
|
||||
//
|
||||
// Section 2. Define the way the DC and/or CS lines are driven (ESP8266 only)
|
||||
//
|
||||
// ##################################################################################
|
||||
|
||||
// Normally the library uses direct register access for the DC and CS lines for speed
|
||||
// If D0 (GPIO16) is used for CS or DC then a different slower method must be used
|
||||
// Uncomment one line if D0 is used for DC or CS
|
||||
// DC on D0 = 6% performance penalty at 40MHz SPI running graphics test
|
||||
// CS on D0 = 2% performance penalty at 40MHz SPI running graphics test
|
||||
|
||||
// #define D0_USED_FOR_DC
|
||||
// #define D0_USED_FOR_CS
|
||||
|
||||
// ##################################################################################
|
||||
//
|
||||
// Section 3. Define the fonts that are to be used here
|
||||
//
|
||||
// ##################################################################################
|
||||
|
||||
// Comment out the #defines below with // to stop that font being loaded
|
||||
// The ESP8366 and ESP32 have plenty of memory so commenting out fonts is not
|
||||
// normally necessary. If all fonts are loaded the extra FLASH space required is
|
||||
// about 17Kbytes. To save FLASH space only enable the fonts you need!
|
||||
|
||||
#define LOAD_GLCD // Font 1. Original Adafruit 8 pixel font needs ~1820 bytes in FLASH
|
||||
#define LOAD_FONT2 // Font 2. Small 16 pixel high font, needs ~3534 bytes in FLASH, 96 characters
|
||||
#define LOAD_FONT4 // Font 4. Medium 26 pixel high font, needs ~5848 bytes in FLASH, 96 characters
|
||||
#define LOAD_FONT6 // Font 6. Large 48 pixel font, needs ~2666 bytes in FLASH, only characters 1234567890:-.apm
|
||||
#define LOAD_FONT7 // Font 7. 7 segment 48 pixel font, needs ~2438 bytes in FLASH, only characters 1234567890:.
|
||||
#define LOAD_FONT8 // Font 8. Large 75 pixel font needs ~3256 bytes in FLASH, only characters 1234567890:-.
|
||||
//#define LOAD_FONT8N // Font 8. Alternative to Font 8 above, slightly narrower, so 3 digits fit a 160 pixel TFT
|
||||
#define LOAD_GFXFF // FreeFonts. Include access to the 48 Adafruit_GFX free fonts FF1 to FF48 and custom fonts
|
||||
|
||||
// Comment out the #define below to stop the SPIFFS filing system and smooth font code being loaded
|
||||
// this will save ~20kbytes of FLASH
|
||||
#define SMOOTH_FONT
|
||||
|
||||
// ##################################################################################
|
||||
//
|
||||
// Section 4. Not used
|
||||
//
|
||||
// ##################################################################################
|
||||
|
||||
|
||||
// ##################################################################################
|
||||
//
|
||||
// Section 5. Other options
|
||||
//
|
||||
// ##################################################################################
|
||||
|
||||
// Define the SPI clock frequency, this affects the graphics rendering speed. Too
|
||||
// fast and the TFT driver will not keep up and display corruption appears.
|
||||
// With an ILI9341 display 40MHz works OK, 80MHz sometimes fails
|
||||
// With a ST7735 display more than 27MHz may not work (spurious pixels and lines)
|
||||
// With an ILI9163 display 27 MHz works OK.
|
||||
// The RPi typically only works at 20MHz maximum.
|
||||
|
||||
// #define SPI_FREQUENCY 1000000
|
||||
// #define SPI_FREQUENCY 5000000
|
||||
// #define SPI_FREQUENCY 10000000
|
||||
// #define SPI_FREQUENCY 20000000
|
||||
#define SPI_FREQUENCY 27000000 // Actually sets it to 26.67MHz = 80/3
|
||||
// #define SPI_FREQUENCY 40000000 // Maximum to use SPIFFS
|
||||
// #define SPI_FREQUENCY 80000000
|
||||
|
||||
// The XPT2046 requires a lower SPI clock rate of 2.5MHz so we define that here:
|
||||
#define SPI_TOUCH_FREQUENCY 2500000
|
||||
|
||||
|
||||
// Comment out the following #define if "SPI Transactions" do not need to be
|
||||
// supported. When commented out the code size will be smaller and sketches will
|
||||
// run slightly faster, so leave it commented out unless you need it!
|
||||
|
||||
// Transaction support is needed to work with SD library but not needed with TFT_SdFat
|
||||
// Transaction support is required if other SPI devices are connected.
|
||||
|
||||
// Transactions are automatically enabled by the library for an ESP32 (to use HAL mutex)
|
||||
// so changing it here has no effect
|
||||
|
||||
// #define SUPPORT_TRANSACTIONS
|
||||
|
|
@ -19,6 +19,15 @@
|
|||
//#define ILI9163_DRIVER
|
||||
//#define S6D02A1_DRIVER
|
||||
//#define RPI_ILI9486_DRIVER // 20MHz maximum SPI
|
||||
//#define HX8357D_DRIVER
|
||||
//#define ILI9481_DRIVER
|
||||
//#define ILI9486_DRIVER
|
||||
//#define ILI9488_DRIVER
|
||||
//#define ST7789_DRIVER
|
||||
//#define ILI9225_DRIVER
|
||||
|
||||
// For IPS LCD display
|
||||
//#define IPS_LCD
|
||||
|
||||
// For M5Stack ESP32 module with integrated display ONLY, remove // in line below
|
||||
//#define M5STACK
|
||||
|
|
@ -26,8 +35,9 @@
|
|||
// For ST7735 and ILI9163 ONLY, define the pixel width and height in portrait orientation
|
||||
//#define TFT_WIDTH 80
|
||||
#define TFT_WIDTH 128
|
||||
#define TFT_HEIGHT 160
|
||||
//#define TFT_HEIGHT 128
|
||||
#define TFT_HEIGHT 160
|
||||
//#define TFT_HEIGHT 240
|
||||
|
||||
// For ST7735 ONLY, define the type of display, originally this was based on the
|
||||
// colour of the tab on the screen protector film but this is not always true, so try
|
||||
|
|
|
|||
|
|
@ -19,6 +19,15 @@
|
|||
#define ILI9163_DRIVER
|
||||
//#define S6D02A1_DRIVER
|
||||
//#define RPI_ILI9486_DRIVER // 20MHz maximum SPI
|
||||
//#define HX8357D_DRIVER
|
||||
//#define ILI9481_DRIVER
|
||||
//#define ILI9486_DRIVER
|
||||
//#define ILI9488_DRIVER
|
||||
//#define ST7789_DRIVER
|
||||
//#define ILI9225_DRIVER
|
||||
|
||||
// For IPS LCD display
|
||||
//#define IPS_LCD
|
||||
|
||||
// For M5Stack ESP32 module with integrated display ONLY, remove // in line below
|
||||
//#define M5STACK
|
||||
|
|
@ -26,8 +35,9 @@
|
|||
// For ST7735 and ILI9163 ONLY, define the pixel width and height in portrait orientation
|
||||
//#define TFT_WIDTH 80
|
||||
#define TFT_WIDTH 128
|
||||
#define TFT_HEIGHT 160
|
||||
//#define TFT_HEIGHT 128
|
||||
#define TFT_HEIGHT 160
|
||||
//#define TFT_HEIGHT 240
|
||||
|
||||
// For ST7735 ONLY, define the type of display, originally this was based on the
|
||||
// colour of the tab on the screen protector film but this is not always true, so try
|
||||
|
|
|
|||
|
|
@ -19,6 +19,15 @@
|
|||
//#define ILI9163_DRIVER
|
||||
#define S6D02A1_DRIVER
|
||||
//#define RPI_ILI9486_DRIVER // 20MHz maximum SPI
|
||||
//#define HX8357D_DRIVER
|
||||
//#define ILI9481_DRIVER
|
||||
//#define ILI9486_DRIVER
|
||||
//#define ILI9488_DRIVER
|
||||
//#define ST7789_DRIVER
|
||||
//#define ILI9225_DRIVER
|
||||
|
||||
// For IPS LCD display
|
||||
//#define IPS_LCD
|
||||
|
||||
// For M5Stack ESP32 module with integrated display ONLY, remove // in line below
|
||||
//#define M5STACK
|
||||
|
|
@ -26,8 +35,9 @@
|
|||
// For ST7735 and ILI9163 ONLY, define the pixel width and height in portrait orientation
|
||||
//#define TFT_WIDTH 80
|
||||
//#define TFT_WIDTH 128
|
||||
//#define TFT_HEIGHT 160
|
||||
//#define TFT_HEIGHT 128
|
||||
//#define TFT_HEIGHT 160
|
||||
//#define TFT_HEIGHT 240
|
||||
|
||||
// For ST7735 ONLY, define the type of display, originally this was based on the
|
||||
// colour of the tab on the screen protector film but this is not always true, so try
|
||||
|
|
|
|||
|
|
@ -18,7 +18,16 @@
|
|||
//#define ST7735_DRIVER
|
||||
//#define ILI9163_DRIVER
|
||||
//#define S6D02A1_DRIVER
|
||||
#define RPI_ILI9486_DRIVER // 20MHz maximum SPI
|
||||
//#define RPI_ILI9486_DRIVER // 20MHz maximum SPI
|
||||
//#define HX8357D_DRIVER
|
||||
//#define ILI9481_DRIVER
|
||||
#define ILI9486_DRIVER
|
||||
//#define ILI9488_DRIVER
|
||||
//#define ST7789_DRIVER
|
||||
//#define ILI9225_DRIVER
|
||||
|
||||
// For IPS LCD display
|
||||
//#define IPS_LCD
|
||||
|
||||
// For M5Stack ESP32 module with integrated display ONLY, remove // in line below
|
||||
//#define M5STACK
|
||||
|
|
@ -26,8 +35,9 @@
|
|||
// For ST7735 and ILI9163 ONLY, define the pixel width and height in portrait orientation
|
||||
//#define TFT_WIDTH 80
|
||||
//#define TFT_WIDTH 128
|
||||
//#define TFT_HEIGHT 160
|
||||
//#define TFT_HEIGHT 128
|
||||
//#define TFT_HEIGHT 160
|
||||
//#define TFT_HEIGHT 240
|
||||
|
||||
// For ST7735 ONLY, define the type of display, originally this was based on the
|
||||
// colour of the tab on the screen protector film but this is not always true, so try
|
||||
|
|
|
|||
|
|
@ -19,6 +19,15 @@
|
|||
//#define ILI9163_DRIVER
|
||||
//#define S6D02A1_DRIVER
|
||||
#define RPI_ILI9486_DRIVER // 20MHz maximum SPI
|
||||
//#define HX8357D_DRIVER
|
||||
//#define ILI9481_DRIVER
|
||||
//#define ILI9486_DRIVER
|
||||
//#define ILI9488_DRIVER
|
||||
//#define ST7789_DRIVER
|
||||
//#define ILI9225_DRIVER
|
||||
|
||||
// For IPS LCD display
|
||||
//#define IPS_LCD
|
||||
|
||||
// For M5Stack ESP32 module with integrated display ONLY, remove // in line below
|
||||
//#define M5STACK
|
||||
|
|
@ -26,8 +35,9 @@
|
|||
// For ST7735 and ILI9163 ONLY, define the pixel width and height in portrait orientation
|
||||
//#define TFT_WIDTH 80
|
||||
//#define TFT_WIDTH 128
|
||||
//#define TFT_HEIGHT 160
|
||||
//#define TFT_HEIGHT 128
|
||||
//#define TFT_HEIGHT 160
|
||||
//#define TFT_HEIGHT 240
|
||||
|
||||
// For ST7735 ONLY, define the type of display, originally this was based on the
|
||||
// colour of the tab on the screen protector film but this is not always true, so try
|
||||
|
|
|
|||
|
|
@ -19,6 +19,15 @@
|
|||
//#define ILI9163_DRIVER
|
||||
//#define S6D02A1_DRIVER
|
||||
//#define RPI_ILI9486_DRIVER // 20MHz maximum SPI
|
||||
//#define HX8357D_DRIVER
|
||||
//#define ILI9481_DRIVER
|
||||
//#define ILI9486_DRIVER
|
||||
//#define ILI9488_DRIVER
|
||||
//#define ST7789_DRIVER
|
||||
//#define ILI9225_DRIVER
|
||||
|
||||
// For IPS LCD display
|
||||
//#define IPS_LCD
|
||||
|
||||
// For M5Stack ESP32 module with integrated display ONLY, remove // in line below
|
||||
//#define M5STACK
|
||||
|
|
|
|||
|
|
@ -19,6 +19,15 @@
|
|||
//#define ILI9163_DRIVER
|
||||
//#define S6D02A1_DRIVER
|
||||
//#define RPI_ILI9486_DRIVER // 20MHz maximum SPI
|
||||
//#define HX8357D_DRIVER
|
||||
//#define ILI9481_DRIVER
|
||||
//#define ILI9486_DRIVER
|
||||
//#define ILI9488_DRIVER
|
||||
//#define ST7789_DRIVER
|
||||
//#define ILI9225_DRIVER
|
||||
|
||||
// For IPS LCD display
|
||||
//#define IPS_LCD
|
||||
|
||||
// For M5Stack ESP32 module with integrated display ONLY, remove // in line below
|
||||
//#define M5STACK
|
||||
|
|
@ -26,8 +35,9 @@
|
|||
// For ST7735 and ILI9163 ONLY, define the pixel width and height in portrait orientation
|
||||
//#define TFT_WIDTH 80
|
||||
#define TFT_WIDTH 128
|
||||
#define TFT_HEIGHT 160
|
||||
//#define TFT_HEIGHT 128
|
||||
#define TFT_HEIGHT 160
|
||||
//#define TFT_HEIGHT 240
|
||||
|
||||
// For ST7735 ONLY, define the type of display, originally this was based on the
|
||||
// colour of the tab on the screen protector film but this is not always true, so try
|
||||
|
|
|
|||
|
|
@ -19,6 +19,15 @@
|
|||
//#define ILI9163_DRIVER
|
||||
//#define S6D02A1_DRIVER
|
||||
//#define RPI_ILI9486_DRIVER // 20MHz maximum SPI
|
||||
//#define HX8357D_DRIVER
|
||||
//#define ILI9481_DRIVER
|
||||
//#define ILI9486_DRIVER
|
||||
//#define ILI9488_DRIVER
|
||||
//#define ST7789_DRIVER
|
||||
//#define ILI9225_DRIVER
|
||||
|
||||
// For IPS LCD display
|
||||
//#define IPS_LCD
|
||||
|
||||
// For M5Stack ESP32 module with integrated display ONLY, remove // in line below
|
||||
//#define M5STACK
|
||||
|
|
@ -26,8 +35,9 @@
|
|||
// For ST7735 and ILI9163 ONLY, define the pixel width and height in portrait orientation
|
||||
//#define TFT_WIDTH 80
|
||||
//#define TFT_WIDTH 128
|
||||
//#define TFT_HEIGHT 160
|
||||
//#define TFT_HEIGHT 128
|
||||
//#define TFT_HEIGHT 160
|
||||
//#define TFT_HEIGHT 240
|
||||
|
||||
// For ST7735 ONLY, define the type of display, originally this was based on the
|
||||
// colour of the tab on the screen protector film but this is not always true, so try
|
||||
|
|
|
|||
Loading…
Reference in New Issue