diff --git a/User_Setups/Setup35_ILI9341_Parallel_STM32F103_Touch_SPI2.h b/User_Setups/Setup35_ILI9341_Parallel_STM32F103_Touch_SPI2.h
new file mode 100644
index 0000000..85e3855
--- /dev/null
+++ b/User_Setups/Setup35_ILI9341_Parallel_STM32F103_Touch_SPI2.h
@@ -0,0 +1,51 @@
+// Define STM32 to invoke STM32 optimised driver
+#define STM32
+
+// Define if Port A pins 7-0 are used for data bus bits 7-0
+#define STM_PORTA_DATA_BUS
+//#define STM_PORTB_DATA_BUS
+//#define STM_PORTC_DATA_BUS
+
+// Tell the library to use 8 bit parallel mode (otherwise SPI is assumed)
+#define TFT_PARALLEL_8_BIT
+
+// Define the TFT display driver
+#define ILI9341_DRIVER
+//#define ILI9488_DRIVER
+
+
+#define TFT_CS PA11 // Chip select control pin
+#define TFT_DC PA12 // Data Command control pin
+#define TFT_RST PA9 // Reset pin
+#define TFT_WR PA8 // Write strobe control pin
+#define TFT_RD PA10 // Read pin
+#define TFT_D0 PA0  // 8 bit parallel bus to TFT
+#define TFT_D1 PA1
+#define TFT_D2 PA2
+#define TFT_D3 PA3
+#define TFT_D4 PA4
+#define TFT_D5 PA5
+#define TFT_D6 PA6
+#define TFT_D7 PA7
+
+#define LOAD_GLCD   // Font 1. Original Adafruit 8 pixel font needs ~1820 bytes in FLASH
+#define LOAD_FONT2  // Font 2. Small 16 pixel high font, needs ~3534 bytes in FLASH, 96 characters
+#define LOAD_FONT4  // Font 4. Medium 26 pixel high font, needs ~5848 bytes in FLASH, 96 characters
+#define LOAD_FONT6  // Font 6. Large 48 pixel font, needs ~2666 bytes in FLASH, only characters 1234567890:-.apm
+#define LOAD_FONT7  // Font 7. 7 segment 48 pixel font, needs ~2438 bytes in FLASH, only characters 1234567890:-.
+#define LOAD_FONT8  // Font 8. Large 75 pixel font needs ~3256 bytes in FLASH, only characters 1234567890:-.
+#define LOAD_GFXFF  // FreeFonts. Include access to the 48 Adafruit_GFX free fonts FF1 to FF48 and custom fonts
+
+// STM32 support for smooth fonts via program memory (FLASH) arrays
+#define SMOOTH_FONT
+
+//---------------- Touch Pad -------------------------------
+
+#define TOUCH_CS PB9
+
+// The XPT2046 requires a lower SPI clock rate of 2.5MHz so we define that here:
+#define SPI_TOUCH_FREQUENCY  2500000
+
+// The STM32F103 has 2 free SPI ports 
+// so uncomment the following line if you want to use second SPI for Touch:   //SPIClass SPITwo(PB15, PB14, PB13); (MOSI, MISO, CLK)
+#define SPI2_for_TOUCH_PORT