diff --git a/User_Setups/Setup207_LilyGo_T_HMI.h b/User_Setups/Setup207_LilyGo_T_HMI.h
index 60af581..8606ef3 100644
--- a/User_Setups/Setup207_LilyGo_T_HMI.h
+++ b/User_Setups/Setup207_LilyGo_T_HMI.h
@@ -1,14 +1,12 @@
 // ST7789 240 x 240 display with no chip select line
-#define USER_SETUP_ID 24
-
-
+#define USER_SETUP_ID 207
 
 #define ST7789_DRIVER // Configure all registers
 
 // #define TFT_RGB_ORDER TFT_BGR // Colour order Blue-Green-Red
 
-#define TFT_WIDTH 240  // ST7789 172 x 320
-#define TFT_HEIGHT 320 // ST7789 240 x 320
+#define TFT_WIDTH 240
+#define TFT_HEIGHT 320
 
 #define CGRAM_OFFSET
 // #define TFT_RGB_ORDER TFT_RGB  // Colour order Red-Green-Blue
@@ -21,17 +19,13 @@
 
 // The ESP32 and TFT the pins used for testing are:
 #define TFT_CS 6  // Chip select control pin (library pulls permanently low
-#define TFT_DC 7  // Data Command control pin - must use a pin in the range 0-31
+#define TFT_DC 7  // Data Command control pin
 #define TFT_RST -1 // Reset pin, toggles on startup
 
-#define TFT_WR 8 // Write strobe control pin - must use a pin in the range 0-31
+#define TFT_WR 8 // Write strobe control pin
 #define TFT_RD -1 // Read strobe control pin
 
-#define TFT_DATA_PIN_OFFSET_EN /* The ESP32S3 controller is controlled by two registers. \
-                                Select data pin numbers higher than 32 to enable this option, \
-                                this macro definition added by Micky -20220701 */
-
-#define TFT_D0 48 // Must use pins in the range 0-31 for the data bus
+#define TFT_D0 48 // Must use pins in the range 0-31 or alternatively 32-48
 #define TFT_D1 47 // so a single register write sets/clears all bits.
 #define TFT_D2 39 // Pins can be randomly assigned, this does not affect
 #define TFT_D3 40 // TFT screen update performance.
@@ -40,7 +34,7 @@
 #define TFT_D6 45
 #define TFT_D7 46
 
-#define TFT_BL 38 // LED back-light (required for M5Stack)
+#define TFT_BL 38 // LED back-light
 
 #define LOAD_GLCD  // Font 1. Original Adafruit 8 pixel font needs ~1820 bytes in FLASH
 #define LOAD_FONT2 // Font 2. Small 16 pixel high font, needs ~3534 bytes in FLASH, 96 characters
@@ -52,12 +46,3 @@
 #define LOAD_GFXFF // FreeFonts. Include access to the 48 Adafruit_GFX free fonts FF1 to FF48 and custom fonts
 
 #define SMOOTH_FONT
-
-// #define SPI_FREQUENCY  27000000
-// #define SPI_FREQUENCY  40000000
-
-// #define SPI_READ_FREQUENCY  20000000
-
-// #define SPI_TOUCH_FREQUENCY  2500000
-
-// #define SUPPORT_TRANSACTIONS
\ No newline at end of file