77 lines
3.5 KiB
C++
77 lines
3.5 KiB
C++
|
|
////////////////////////////////////////////////////////////
|
|
// //
|
|
// HomeSpan: A HomeKit implementation for the ESP32 //
|
|
// ------------------------------------------------ //
|
|
// //
|
|
// Example 9: Logging messages to the Serial Monitor //
|
|
// //
|
|
// //
|
|
////////////////////////////////////////////////////////////
|
|
|
|
#include "HomeSpan.h"
|
|
#include "DEV_LED.h"
|
|
#include "DEV_Identify.h"
|
|
|
|
void setup() {
|
|
|
|
// HomeSpan sends a variety of messages to the Serial Monitor of the Arduino IDE whenever the device is connected
|
|
// to a computer. Message output is performed either by the usual Serial.print() function, or by one of two macros,
|
|
// LOG1() and LOG2(). These two macros call Serial.print() depending on HomeSpan's Log Level setting. A setting
|
|
// of 0 means that LOG1() and LOG2() messages are ignored. A setting of 1 causes HomeSpan to print LOG1() messages
|
|
// to the Serial Monitor, but ignores LOG2() message. And a setting of 2 causes HomeSpan to print both LOG1() and
|
|
// LOG2() messages.
|
|
|
|
// Example 9 illustrates how to add such log messages. The code is identical to Example 8 (without comments), except
|
|
// that Serial.print() and LOG1() messages have been added to DEV_LED.h. The Serial.print() messages will always be
|
|
// output to the Arduino Serial Monitor. The LOG1() messages will only be output if the Log Level is set to 1 or 2.
|
|
|
|
// The setLogLevel() method of homeSpan is used to change the log level as follows:
|
|
|
|
// homeSpan.setLogLevel(0) - sets Log Level to 0
|
|
// homeSpan.setLogLevel(1) - sets Log Level to 1
|
|
// homeSpan.setLogLevel(2) - sets Log Level to 2
|
|
|
|
// The method should be called BEFORE homeSpan.begin() - see below for proper use.
|
|
|
|
// RECOMMENDATION: Since a HomeSpan ESP32 is meant to be physically connected to real-world devices, you may find
|
|
// yourself with numerous ESP32s each configured with a different set of Accessories. To aid in identification
|
|
// you may want to add Serial.print() statements containing some sort of initialization message to the constructors for
|
|
// each derived Service, such as DEV_LED. Doing so allows HomeSpan to "report" on its configuration upon start-up. See
|
|
// DEV_LED for examples.
|
|
|
|
Serial.begin(115200);
|
|
|
|
homeSpan.setLogLevel(1); // NEW - Sets Log Level to 1, which causes LOG1() messages to be output
|
|
|
|
homeSpan.begin(Category::Bridges,"HomeSpan Bridge");
|
|
|
|
// Defines the Bridge Accessory
|
|
|
|
new SpanAccessory();
|
|
new DEV_Identify("Bridge #1","HomeSpan","123-ABC","HS Bridge","0.9",3);
|
|
new Service::HAPProtocolInformation();
|
|
new Characteristic::Version("1.1.0");
|
|
|
|
// Defines an ON/OFF LED Accessory attached to pin 16
|
|
|
|
new SpanAccessory();
|
|
new DEV_Identify("On/Off LED","HomeSpan","123-ABC","20mA LED","0.9",0);
|
|
new DEV_LED(16);
|
|
|
|
// Defines a Dimmable LED Accessory attached to pin 17 using PWM channel 0
|
|
|
|
new SpanAccessory();
|
|
new DEV_Identify("Dimmable LED","HomeSpan","123-ABC","20mA LED","0.9",0);
|
|
new DEV_DimmableLED(0,17);
|
|
|
|
} // end of setup()
|
|
|
|
//////////////////////////////////////
|
|
|
|
void loop(){
|
|
|
|
homeSpan.poll();
|
|
|
|
} // end of loop()
|